Sitat fra: -Aleks på torsdag 30. april 2015, klokken 12:51Goodyear EfficientGrip Performance 2 er helt topp. Jeg kjører på 225/40-18 på 8x18" felg og er kjempefornøyd. Litt dekkstøy vil det alltid være på en elektrisk bil da dette sammen med vindstøy er det eneste av lyd bilen "lager"
Hva er det folket her med felger 18"+ kjører på av typen dekk?
Har selv 18x8" felger med 215/40/18 Vredestein ultrac cento og synes disse støyer noe helt forjævlig...
Ikke fornøyd
- Velkommen til Elbilforum.no.
Bli medlem i Norsk elbilforening og støtt driften av Elbilforum. Som medlem får du i tillegg startpakke, medlemsfordeler og gode tips om elbil og lading. Du blir med i et fellesskap som jobber for mindre utslipp fra veitrafikken. Medlemskap koster 485 kroner per år. elbil.no/medlemskap
Denne delen lar deg se alle innlegg laget av dette medlemmet. Merk at du bare kan se innlegg gjort i områder du har tilgang til.
#1
e-Golf / Sv: Felg og dekk
torsdag 30. april 2015, klokken 18:22
#2
e-Golf / Sv: VCDS Tweaks e-Golf
mandag 27. april 2015, klokken 13:57Sitat fra: Tbg på søndag 26. april 2015, klokken 23:08Min var levert med svart display. Muligens fordi den er bruktimportert fra Tyskland, eller fordi det er litt hipp som happ hos VW av og til
Trodde dette var standar med carbonlook? Jeg har det på min uten å ha kodet opp selv? :S
#3
e-Golf / Sv: VCDS Tweaks e-Golf
søndag 26. april 2015, klokken 19:14Sitat fra: hottentott33 på lørdag 25. april 2015, klokken 18:20Sitat fra: EL-John på lørdag 25. april 2015, klokken 16:36
Kan bekrefte at dette nå virker på bilen min. Det er nå carbon i displayet i midten
#4
e-Golf / Sv: VCDS Tweaks e-Golf
lørdag 25. april 2015, klokken 16:36Change instruments to Carbon Fiber look
17 Instruments
STG adjustment > function 10
Select "channel display representation" (displaydarstellung)
Change to "Version 2" (default is version 1)
[/quote]
Kan bekrefte at dette nå virker på bilen min. Det er nå carbon i displayet i midten
#5
e-Golf / Sv: VCDS Tweaks e-Golf
lørdag 25. april 2015, klokken 16:31Sitat fra: Råde på fredag 24. april 2015, klokken 21:01Kan bekrefte at parkbremsen kommer på sammen med et varsels pling, viss bilen står i gir.Sitat fra: EL-John på fredag 24. april 2015, klokken 18:06Ja, hvis bilen står i "gir" så får du pipingen i tillegg til at parkbremsen går på (på min i hvert fall).Sitat fra: Råde på torsdag 23. april 2015, klokken 21:06Det har jeg ikke registrert, er det automatisk parkbrems viss man åpner førerdøren?
Nope. Skru på bilen feil?
El-John: går parkbremsen på allikevel?
#6
e-Golf / Sv: VCDS Tweaks e-Golf
fredag 24. april 2015, klokken 18:06Sitat fra: Råde på torsdag 23. april 2015, klokken 21:06Det har jeg ikke registrert, er det automatisk parkbrems viss man åpner førerdøren?
Nope. Skru på bilen feil?
El-John: går parkbremsen på allikevel?
#7
e-Golf / Sv: VCDS Tweaks e-Golf
torsdag 23. april 2015, klokken 18:21Sitat fra: EL-John på søndag 12. april 2015, klokken 21:54Denne kan du Legge inn i første posten din poskare. Kan bekrefte at dette virkerSitat fra: mihkku på søndag 12. april 2015, klokken 20:00Fra VWVortex Forum.
Burde få med hvordan fjerne den irriterendes alarmen hver gang førerdøren åpnes når bilen står på. Irriterendes funksjon når man må ut for å lade eller åpne garasjeporten.
Disable the annoying tone when the ignition and driver's door open.
17 Instruments
Adaptations
Ignition active message; Trigger
Change to "No display" (default value: driver's door)
German translation for this is.....
German translation.....
STG 17 (Schalttafeleinsatz) auswählen
STG Anpassung -> Funktion 10
Zündung aktiv Meldung; Auslöser
ändern auf "Keine Anzeige"
#8
e-Golf / Sv: VCDS Tweaks e-Golf
fredag 17. april 2015, klokken 19:59Sitat fra: poskare på fredag 17. april 2015, klokken 13:44
Er du HELDIG kan du finne en VCDS kopi på ebay som fungerer med nåværende versjon av SW, men kommer det oppdateringer som støtter e-Golfen bedre i fremtiden, vil løpet være kjørt, anbefaler deg ikke ebay kopi.
Grunnen til dette er at lisensen for å bruke programvaren ligger i kabelen, så når de kommer med ny programversjon fungerer 99,9% av kinakopiene ikke lenger.
Enig med deg der Poskare.
Ross Tech er helt klart den mest utbredte og etter min mening beste leverandør av VCDS. Jeg har hatt samme kabel nå i 5 år og brukt den til diverse produkter fra VAG gruppen med stort smil om munnen vær gang.
Ross Tech er også flink med å sende ut aktuelle oppdateringer relativt raskt dette gjelder seg både for firmware og SW.
Finnes 2-3 ulike produsenter, og tror Ross-Tech er den som er mest utbredt.
http://ross-tech.com
#9
e-Golf / Sv: VCDS Tweaks e-Golf
onsdag 15. april 2015, klokken 10:54Sitat fra: poskare på onsdag 15. april 2015, klokken 07:39
Ah! Jeg hadde lys i posisjon OFF. Må testes på nytt! Takk EL-John! Legger posten din inn i første post i løpet av dagen! [emoji106]
#10
e-Golf / Sv: VCDS Tweaks e-Golf
onsdag 15. april 2015, klokken 00:50
Jeg fulgte også denne prosedyren etter koding.
Part 3: Auto RainClose - In-Car, setup procedures
Auto RainClose - Factory reset procedure
This tweak requires that the control unit be reset after the coding changes above have been made. This is done using the following steps:
Press the CAR button on the RH side of the Discover media Unit
Press the set-up panel on the bottom RH side of the screen
Select Factory Setting panel (it's the very last entry on the list)
On the Factory Setting screen, select Opening and Closing
Press the Reset panel
Auto RainClose -Menu enabling procedure
For Auto RainClose to work, the function must first be enabled in the Discover media screen. This is done using the following steps:
Press the CAR button on the RH side of the Discover media Unit
Press the set-up panel on the bottom RH side of the screen
Press the Opening and Closing panel
Place a tick in the Automatic closing in rain panel as shown in the picture below.
Make sure that the settings for all other options in Opening and closing are appropriate and that they have not been changed by the factory reset process above (e.g. check that Convenience opening option isn't set to "off")
Exit the screen
Også er det viktig at disse kriteriene er fulgt for at det skal virke.
Auto RainClose - Test and operating procedure
Make sure that the wiper stalk is in the rain sensing position (i.e. up one position) and that the headlights are switched to the Auto position
Wind down one, or more windows, and/or sunroof
exit and lock the vehicle using the remote fob or KESSY
Wait a minute, or two and pour water on the rain sensor, or tap the rain sensor with your fingers.
The open window(s)/sunroof should close
Note 5: a further feature of this tweak is that if the window(s)/sunroof is left open for an extended time (generally overnight) without rain, or intervention, the open aperture(s) will be automatically shut.
Part 3: Auto RainClose - In-Car, setup procedures
Auto RainClose - Factory reset procedure
This tweak requires that the control unit be reset after the coding changes above have been made. This is done using the following steps:
Press the CAR button on the RH side of the Discover media Unit
Press the set-up panel on the bottom RH side of the screen
Select Factory Setting panel (it's the very last entry on the list)
On the Factory Setting screen, select Opening and Closing
Press the Reset panel
Auto RainClose -Menu enabling procedure
For Auto RainClose to work, the function must first be enabled in the Discover media screen. This is done using the following steps:
Press the CAR button on the RH side of the Discover media Unit
Press the set-up panel on the bottom RH side of the screen
Press the Opening and Closing panel
Place a tick in the Automatic closing in rain panel as shown in the picture below.
Make sure that the settings for all other options in Opening and closing are appropriate and that they have not been changed by the factory reset process above (e.g. check that Convenience opening option isn't set to "off")
Exit the screen
Også er det viktig at disse kriteriene er fulgt for at det skal virke.
Auto RainClose - Test and operating procedure
Make sure that the wiper stalk is in the rain sensing position (i.e. up one position) and that the headlights are switched to the Auto position
Wind down one, or more windows, and/or sunroof
exit and lock the vehicle using the remote fob or KESSY
Wait a minute, or two and pour water on the rain sensor, or tap the rain sensor with your fingers.
The open window(s)/sunroof should close
Note 5: a further feature of this tweak is that if the window(s)/sunroof is left open for an extended time (generally overnight) without rain, or intervention, the open aperture(s) will be automatically shut.
#11
e-Golf / Sv: VCDS Tweaks e-Golf
tirsdag 14. april 2015, klokken 23:33
Klarte ikke å vente!
Kodingen var nok trikset, nå funker automatisk lukking av vindu ved regn som bare det
Kodingen var nok trikset, nå funker automatisk lukking av vindu ved regn som bare det
#12
e-Golf / Sv: VCDS Tweaks e-Golf
tirsdag 14. april 2015, klokken 23:02
Automatisk lukking av vinduer ved regn: (Denne virket ikke som den skulle i dag når det kom noen drypp, forsker videre på denne, da jeg leste om noen som hadde funnet ut noe, ett eller annet sted)
[/quote]
Fikk heller ikke dette til å virke etter å ha utført tweak.
Rotet litt rundt og fant denne. Sjekker ut om det virker i morgen og kommer tilbake med evt. Resultat.
Auto Rain Close -mk7 VCDS tweak
Background
It's fair to say that the Auto RainClose tweak has had a dubious infancy when applied to MQB platform vehicles like the mk7 Golf. My understanding from conversations on various forums is that problems were first encountered with this tweak because of the new sensor that was installed in these cars.
In previous models, VW used a "RLS" (i.e. Rain Light Sensor) to control Auto RainClose. However, in many of the mk7 models, the sensor that was introduced was the "RLFS" (Rain Light Humidity Sensor, or in German, Regen, Licht, Feuchte Sensor). Some VCDS auto-scan listings now report this new sensor as its Anglicized name, "RLHS" and of late, the RLS seems to have re-appeared in some mk7 scan reports (particularly in NAR cars).
As a result of early problems with the Auto RainClose tweak, the folk at Ross Tech (i.e. the inestimable Dana) modified the VCDS software so that it would communicate correctly with these new sensor units. The first SW version in which these changes appeared was Beta ver. 14.6.1. At the time of writing, Ross Tech has advised that their Beta software (i.e. currently Beta 14.8.1) is still the only version with the necessary smarts to talk to the sensors on mk7 vehicles. Doubtless, in the fullness of time (to quote Sir Humphrey Appleby), RT's non-beta software will be modified to accommodate these new sensors.
Edit - Nov 2014: Ross-Tech's full version software (SW version commencing with the number "14", or greater) is now able to fully communicate with the rain sensors in mk7 vehicles.
The material in these instructions have been sourced from numerous forums and a skeletal version of these procedures can be found on the Stemie.de site.
Particular acknowledgement is given to the findings of the folk on the VCDS thread on VWvortex. In addition, recognition must also be given to those talented and amazing VCDS gurus on the Ross Tech forum for unravelling the early problems with the RLFS. Thanks to you all for your valuable contributions.
A word of caution for those that wish to proceed. This is one of the more complex tweaks and as a result, particular care and precision in following these instructions is required. Feedback from others indicates that a few have not been able to make this tweak work albeit I have received lots of reports of its successful implementation. If you fall into the latter category-congratulations. For those in the former category, please revert all settings to their original values (and re-check the entries for "opening and closing" in the Discover media screen which may have altered because of the factory reset process-see part 3 of these instructions). And, if you have implemented this tweak and you want to revert back to the car's original settings, make sure that you use RT's Beta software for the roll-back process.
If others can add to the information in these tweak instructions, please do so. If you want to PM, I'll undertake to modify this post with any updates - or you can add your own separate post to this thread.
For ease of understanding, these instructions have been broken-up into three discrete parts as follows (it is recommended that the instructions should be followed in the sequence listed):
This Post
Part 1: Auto RainClose - Coding Changes
Post #230
Part 2: Auto RainClose - Adaptation Channel Changes
Part 3: Auto RainClose - In-Car, setup procedures
All parts must be completed
Ross-Tech software version commencing with a number "14", or greater must be used for this tweak
Part 1: Auto RainClose - Coding Changes
1. From the Installed tab on the Select Control Module screen, select 09-Cent. Elect.
2. On the Open Controller screen for address 09 - Cent. Elect., click the Coding - 07 tab
3. When the screen below opens, click on the pull-down down tab in the middle of the screen (as shown next to the red arrow). As indicated in the picture, the BCM (Body Control Module) has two "slave" modules, one of which is the RLFS
4, Select RLFS and click on the Long Coding Helper
http://i.imgur.com/oeLX4Np.png
Note 1: on some mk7 vehicles, the slave module will be RLS, or RLHS
5. Select Byte 0 and place a tick in Bit 1 and Bit 2 as shown in the picture below. Exit this screen
http://i.imgur.com/mmC3m1Y.png
6. When the screen below appears, ensure that the New coding box contains the Hexadecimal value 06A8DD Click the Do it! tab. Go back to the open controller screen
http://i.imgur.com/KEjMKpq.png
Note 2: some forums report "error 31" message at this point. If this error message appears, manually enter 06A8DD into the New coding box instead of using the Long Coding Helper. Then click the Do it! tab
Note 3: On some mk7 vehicles, the default coding string for the rain sensor is 01E8DD. If this is the case, the required hexadecimal value in the new coding box is 07E8DD.
Go to Part 2(next post)
[/quote]
Fikk heller ikke dette til å virke etter å ha utført tweak.
Rotet litt rundt og fant denne. Sjekker ut om det virker i morgen og kommer tilbake med evt. Resultat.
Auto Rain Close -mk7 VCDS tweak
Background
It's fair to say that the Auto RainClose tweak has had a dubious infancy when applied to MQB platform vehicles like the mk7 Golf. My understanding from conversations on various forums is that problems were first encountered with this tweak because of the new sensor that was installed in these cars.
In previous models, VW used a "RLS" (i.e. Rain Light Sensor) to control Auto RainClose. However, in many of the mk7 models, the sensor that was introduced was the "RLFS" (Rain Light Humidity Sensor, or in German, Regen, Licht, Feuchte Sensor). Some VCDS auto-scan listings now report this new sensor as its Anglicized name, "RLHS" and of late, the RLS seems to have re-appeared in some mk7 scan reports (particularly in NAR cars).
As a result of early problems with the Auto RainClose tweak, the folk at Ross Tech (i.e. the inestimable Dana) modified the VCDS software so that it would communicate correctly with these new sensor units. The first SW version in which these changes appeared was Beta ver. 14.6.1. At the time of writing, Ross Tech has advised that their Beta software (i.e. currently Beta 14.8.1) is still the only version with the necessary smarts to talk to the sensors on mk7 vehicles. Doubtless, in the fullness of time (to quote Sir Humphrey Appleby), RT's non-beta software will be modified to accommodate these new sensors.
Edit - Nov 2014: Ross-Tech's full version software (SW version commencing with the number "14", or greater) is now able to fully communicate with the rain sensors in mk7 vehicles.
The material in these instructions have been sourced from numerous forums and a skeletal version of these procedures can be found on the Stemie.de site.
Particular acknowledgement is given to the findings of the folk on the VCDS thread on VWvortex. In addition, recognition must also be given to those talented and amazing VCDS gurus on the Ross Tech forum for unravelling the early problems with the RLFS. Thanks to you all for your valuable contributions.
A word of caution for those that wish to proceed. This is one of the more complex tweaks and as a result, particular care and precision in following these instructions is required. Feedback from others indicates that a few have not been able to make this tweak work albeit I have received lots of reports of its successful implementation. If you fall into the latter category-congratulations. For those in the former category, please revert all settings to their original values (and re-check the entries for "opening and closing" in the Discover media screen which may have altered because of the factory reset process-see part 3 of these instructions). And, if you have implemented this tweak and you want to revert back to the car's original settings, make sure that you use RT's Beta software for the roll-back process.
If others can add to the information in these tweak instructions, please do so. If you want to PM, I'll undertake to modify this post with any updates - or you can add your own separate post to this thread.
For ease of understanding, these instructions have been broken-up into three discrete parts as follows (it is recommended that the instructions should be followed in the sequence listed):
This Post
Part 1: Auto RainClose - Coding Changes
Post #230
Part 2: Auto RainClose - Adaptation Channel Changes
Part 3: Auto RainClose - In-Car, setup procedures
All parts must be completed
Ross-Tech software version commencing with a number "14", or greater must be used for this tweak
Part 1: Auto RainClose - Coding Changes
1. From the Installed tab on the Select Control Module screen, select 09-Cent. Elect.
2. On the Open Controller screen for address 09 - Cent. Elect., click the Coding - 07 tab
3. When the screen below opens, click on the pull-down down tab in the middle of the screen (as shown next to the red arrow). As indicated in the picture, the BCM (Body Control Module) has two "slave" modules, one of which is the RLFS
4, Select RLFS and click on the Long Coding Helper
http://i.imgur.com/oeLX4Np.png
Note 1: on some mk7 vehicles, the slave module will be RLS, or RLHS
5. Select Byte 0 and place a tick in Bit 1 and Bit 2 as shown in the picture below. Exit this screen
http://i.imgur.com/mmC3m1Y.png
6. When the screen below appears, ensure that the New coding box contains the Hexadecimal value 06A8DD Click the Do it! tab. Go back to the open controller screen
http://i.imgur.com/KEjMKpq.png
Note 2: some forums report "error 31" message at this point. If this error message appears, manually enter 06A8DD into the New coding box instead of using the Long Coding Helper. Then click the Do it! tab
Note 3: On some mk7 vehicles, the default coding string for the rain sensor is 01E8DD. If this is the case, the required hexadecimal value in the new coding box is 07E8DD.
Go to Part 2(next post)
#13
e-Golf / Sv: VCDS Tweaks e-Golf
søndag 12. april 2015, klokken 23:22Sitat fra: poskare på søndag 12. april 2015, klokken 23:16Kjempe god ide
Tenker jeg også etterhvert legger inn i første post, alle ønskene som har dukket opp her, så vil Råde og/eller jeg teste disse så fort vi får anledning. Eller noen av dere andre som har kabel selvsagt!Da legger jeg de inn i første post med "cred" til de som har testet og bekreftet at de fungerer!
God idé?
#14
e-Golf / Sv: VCDS Tweaks e-Golf
søndag 12. april 2015, klokken 22:00
Har ikke fått sjekket om dette funker på e-Golf, men hadde vært morsomt
#15
e-Golf / Sv: VCDS Tweaks e-Golf
søndag 12. april 2015, klokken 21:54Sitat fra: mihkku på søndag 12. april 2015, klokken 20:00Fra VWVortex Forum.
Burde få med hvordan fjerne den irriterendes alarmen hver gang førerdøren åpnes når bilen står på. Irriterendes funksjon når man må ut for å lade eller åpne garasjeporten.
Disable the annoying tone when the ignition and driver's door open.
17 Instruments
Adaptations
Ignition active message; Trigger
Change to "No display" (default value: driver's door)
German translation for this is.....
German translation.....
STG 17 (Schalttafeleinsatz) auswählen
STG Anpassung -> Funktion 10
Zündung aktiv Meldung; Auslöser
ändern auf "Keine Anzeige"
